Novak 5463 3A High-Voltage BEC (55-5463-7) Manuel d'utilisateur télécharger pdf

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

#5463 3A HIGH-

VOLTAGE BEC

MODULE

Novak BECs (Battery Eliminator Circuits) regulate the main

battery pack voltages to 6VDC output, to provide safe and

consistent servo and receiver power throughout the charge

without the need for a separate receiver pack.

Input Voltage Specication .............. 2-6S LiPo / 4-18 NiMH cells

WARNING! Always make sure the main battery pack is fully-

charged before operating model. This BEC can NOT supply

power to the radio system & you will NOT have control of

model if main battery pack becomes discharged or fails.

In no way shall Novak R/C, Inc. be responsible or liable for any

damage or loss which may occur from use of this product.

GENERAL INSTALLATION (continued on back):

Find a space in your vehicle to mount the BEC that is close to

the main battery pack & receiver. Use the included tie-wraps

or double-sided tape to mount the BEC and its power switch.

2. Find a convenient place to solder the BEC’s RED & BLACK

power wires to the vehicle’s main battery pack--

o the battery

connector, or ESC’s positive & negative solder tabs where

battery

power capacitor wires are soldered in electric vehicle

Shorten the BEC’s power wires if possible.

3. Plug the 3-pin JST connector on the BEC’s power output

lead into any open slot in the receiver. Make sure the polarity

is correct--

the black wire will be towards the outside on most

receivers and the red will be towards the center of the receiver

#55-5463-7 12/2014

1 2

Résumé du contenu

Page 1

#5463 3A HIGH-VOLTAGE BEC MODULENovak BECs (Battery Eliminator Circuits) regulate the main battery pack voltages to 6VDC output, to provide safe and c

Page 2

remove&insulateredwireblack wire to battery negativered wire to battery positivepoweroutput lead4. For Electric Vehicle Installations, remove

Commentaires sur ces manuels

Pas de commentaire

Novak 5463 3A High-Voltage BEC (55-5463-7) Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Novak 5463 3A High-Voltage BEC (55-5463-7). Novak 5463 3A High-Voltage BEC (55-5463-7) User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Novak 5463 3A High-Voltage BEC (55-5463-7)